View PS9822-2-F3-N-AX_515554.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PRELIMINARY DATA SHEET
PHOTOCOUPLER
PS9822-1,-2
1 Mbps OPEN COLLECTOR OUTPUT TYPE 8-PIN SSOP (SO-8) HIGH-SPEED PHOTOCOUPLER
DESCRIPTION
The PS9822-1 and PS9822-2 are active-low type high-speed photocouplers that use a GaAlAs light-emitting diode on the input side and a photodetector IC that includes a photodiode and a signal processor on the same chip on the output side. The PS9822-1, -2 are high-speed digital output type photocouplers designed specifically for low circuit current. The PS9822-2 is suitable for high density applications. -NEPOC Series-
FEATURES
* Supply Voltage N rank: VCC = 3.3 V L rank: VCC = 5 V * Pulse width distortion (tPHL-tPLH = 200 ns MAX.) * 40% reduction of mounting area (5-pin SOP x 2) * High-speed (1 Mbps) * High isolation voltage (BV = 2 500 Vr.m.s.) * Open collector output * Ordering number of tape product : PS9822-1-F3: 1 500 pcs/reel : PS9822-2-F3: 1 500 pcs/reel * Pb-Free product
8 1 8
PIN CONNECTION
(Top View)
PS9822-1 765
2
3
4
1. NC 2. Anode 3. Cathode 4. NC 5. GND 6. VO 7. NC 8. VCC
PS9822-2 765
* PoE (Power over Ethernet) * Measurement equipment * FA Network
1 2
SHIELD
3
4
TRUTH TABLE
LED ON OFF Output L H
The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version.
Document No. PN10698EJ01V0DS (1st edition) Date Published January 2008 NS
SHIELD
APPLICATIONS
1. Anode1 2. Cathode1 3. Cathode2 4. Anode2 5. GND 6. VO2 7. VO1 8. VCC
2008
PS9822-1,-2
PACKAGE DIMENSIONS (UNIT: mm)
5.210.25 8 5
6.00.2 1 4 3.950.1
3.270.2
0.15 +0.10 -0.05
0.10.1
1.27 0.4 +0.10 -0.05 0.25 M
0.50.3 0.10 S
MARKING EXAMPLE
PS9822-1
PS9822-2
Type Number Assembly Lot
9822-1 NT731
N
N T 7 31
No. 1 pin Mark Initial of NEC (Engraved mark)
9822-2 NT731
N
N T 7 31
No. 1 pin Mark Initial of NEC (Engraved mark)
Type Number Assembly Lot
Week Assembled Year Assembled (Last 1 Digit)
Week Assembled Year Assembled (Last 1 Digit)
In-house Code (T: Pb-Free)
Rank Code
In-house Code (T: Pb-Free)
Rank Code
2
Preliminary Data Sheet PN10698EJ01V0DS
PS9822-1,-2
ORDERING INFORMATION
Part Number PS9822-1 Order Number PS9822-1-AX Rank N L PS9822-1-F3 PS9822-1-F3-AX
*1
Solder Plating Specification Pb-Free
Packing Style 20 pcs (Tape 20 pcs cut)
*2
N L
*1
Embossed Tape 1 500 pcs/reel
*2
PS9822-2
PS9822-2-AX
N L
*1
20 pcs (Tape 20 pcs cut)
*2
PS9822-2-F3
PS9822-2-F3-AX
N L
*1
Embossed Tape 1 500 pcs/reel
*2
*1 N rank: VCC = 3.3 V *2 L rank: VCC = 5 V
Preliminary Data Sheet PN10698EJ01V0DS
3
PS9822-1,-2
ABSOLUTE MAXIMUM RATINGS (TA = 25C, unless otherwise specified)
Parameter Symbol Ratings PS9822-1 Diode Forward Current Reverse Voltage
Detector
Unit
PS9822-2 15 5 7 7 25 40
*2
IF VR VCC VO IO
*3
20
*1
mA V/ch V V/ch mA/ch mW/ch Vr.m.s. C C
Supply Voltage Output Voltage Output Current Power Dissipation
PC BV TA Tstg
Isolation Voltage
*4
2 500 -40 to +100 -55 to +125
Operating Ambient Temperature Storage Temperature
*1 Reduced to 0.3 mA/C at TA = 60C or more. *2 Reduced to 0.1 mA/C at TA = 60C or more. *3 Applies to output pin VO (collector pin). Reduced to 1.5 mW/C at TA = 65C or more. *4 AC voltage for 1 minute at TA = 25C, RH = 60% between input and output. Pins 1-4 shorted together, 5-8 shorted together.
RECOMMENDED OPERATING CONDITIONS
Parameter Low Level Input Voltage High Level Input Current Supply Voltage N rank L rank Pull-up Resistance TLL (RL = 1.0 k, loads) RL N Symbol VFL IFH VCC MIN. 0 6.3 2.7 4.5 330 10 3.3 5. 0 TYP. MAX. 0.8 12.5 3.6 5.5 4k 5 Unit V mA V
4
Preliminary Data Sheet PN10698EJ01V0DS
PS9822-1,-2
ELECTRICAL CHARACTERISTICS: N rank (TA = -40 to +100C, unless otherwise specified)
Parameter Diode Forward Voltage Reverse Current Terminal Capacitance Detector High Level Output Current Low Level Output Voltage High Level Supply Current Low Level Supply Current Coupled Threshold Input Current (H L) Isolation Resistance RI-O VI-O = 1 kVDC, RH = 40 to 60%, TA = 25C Isolation Capacitance Propagation Delay Time (H L) Propagation Delay Time (L H) Pulse Width Distortion (PWD) tPHL-tPLH VCC = 3.3 V, RL = 350 , IF = 7.5 mA, VTHHL = VTHLH = 1.5 V 200 ns tPLH CI-O tPHL V = 0 V, f = 1 MHz, TA = 25C VCC = 3.3 V, RL = 350 , IF = 7.5 mA, VTHHL = VTHLH = 1.5 V 700 0.6 500 pF ns 10
11 *2
Symbol VF IR Ct IOH VOL ICCH ICCL IFHL
Conditions IF = 10 mA, TA = 25C VR = 3 V, TA = 25C V = 0 V, f = 1 MHz, TA = 25C VCC = VO = 3.3 V, VF = 0.8 V VCC = 3.3 V, IF = 5 mA, IOL = 13 mA VCC = 3.3 V, IF = 0 mA, VO = Open VCC = 3.3 V, IF = 10 mA, VO = Open VCC = 3.3 V, VO = 0.8 V, RL = 350
MIN.
TYP. 1.6
*1
MAX. 1.8 10
Unit V
A
pF
30 1 0.2 100 0.6 2 3 5
A
V mA/ch
mA
*1 Typical values at TA = 25C *2 Because VOL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device.
Preliminary Data Sheet PN10698EJ01V0DS
5
PS9822-1,-2
ELECTRICAL CHARACTERISTICS: L rank (TA = -40 to +100C, unless otherwise specified)
Parameter Diode Forward Voltage Reverse Current Terminal Capacitance Detector High Level Output Current Low Level Output Voltage High Level Supply Current Low Level Supply Current Coupled Threshold Input Current (H L) Isolation Resistance RI-O VI-O = 1 kVDC, RH = 40 to 60%, TA = 25C Isolation Capacitance Propagation Delay Time (H L) Propagation Delay Time (L H) Pulse Width Distortion (PWD) tPHL-tPLH VCC = 5 V, RL = 350 , IF = 7.5 mA, VTHHL = VTHLH = 1.5 V 200 ns tPLH CI-O tPHL V = 0 V, f = 1 MHz, TA = 25C VCC = 5 V, RL = 350 , IF = 7.5 mA, VTHHL = VTHLH = 1.5 V 700 0.6 500 pF ns 10
11 *2
Symbol VF IR Ct IOH VOL ICCH ICCL IFHL
Conditions IF = 10 mA, TA = 25C VR = 3 V, TA = 25C V = 0 V, f = 1 MHz, TA = 25C VCC = VO = 5 V, VF = 0.8 V VCC = 5 V, IF = 5 mA, IOL = 13 mA VCC = 5 V, IF = 0 mA, VO = Open VCC = 5 V, IF = 10 mA, VO = Open VCC = 5 V, VO = 0.8 V, RL = 350
MIN.
TYP. 1.6
*1
MAX. 1.8 10
Unit V
A
pF
30 1 0.2 100 0.6 2.5 3.5 5
A
V mA/ch
mA
*1 Typical values at TA = 25C *2 Because VOL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device.
6
Preliminary Data Sheet PN10698EJ01V0DS
PS9822-1,-2
TAPING SPECIFICATIONS (UNIT: mm)
Outline and Dimensions (Tape)
5.560.1
2.00.05 4.00.1
1.750.1
1.5+0.1 -0
4.05 MAX.
1.70.1 8.00.1
12.00.2
5.50.1
6.40.1
3.60.1
0.30.05
Taping Direction
PS9822-1-F3 PS9822-2-F3
Outline and Dimensions (Reel)
2.00.5
2.00.5 13.00.2
R 1.0
21.00.8
3302.0
13.00.2
1001.0
13.51.0 17.51.0
Packing: 1 500 pcs/reel
11.9 to 15.4 Outer edge of flange
Preliminary Data Sheet PN10698EJ01V0DS
7
PS9822-1,-2
RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm)
1.45
5.25
8
Preliminary Data Sheet PN10698EJ01V0DS
1.27
0.8
PS9822-1,-2
NOTES ON HANDLING 1. Recommended soldering conditions
(1) Infrared reflow soldering * Peak reflow temperature * Time of peak reflow temperature * Time of temperature higher than 220C * Time to preheat temperature from 120 to 180C * Number of reflows * Flux 260C or below (package surface temperature) 10 seconds or less 60 seconds or less 12030 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.)
Recommended Temperature Profile of Infrared Reflow
Package Surface Temperature T (C)
(heating) to 10 s 260C MAX. 220C to 60 s 180C 120C 12030 s (preheating)
Time (s)
(2) Wave soldering * Temperature * Time * Preheating conditions * Number of times * Flux 260C or below (molten solder temperature) 10 seconds or less 120C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by soldering iron * Peak temperature (lead part temperature) * Time (each pins) * Flux 350C or below 3 seconds or less Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead. (b) Please be sure that the temperature of the package would not be heated over 100C.
Preliminary Data Sheet PN10698EJ01V0DS
9
PS9822-1,-2
(4) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
2. Cautions regarding noise
Be aware that when voltage is applied suddenly between the photocoupler's input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings.
USAGE CAUTIONS
1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 F is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity.
10
Preliminary Data Sheet PN10698EJ01V0DS
PS9822-1,-2
* The information in this document is current as of January, 2008. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. * NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. * NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above).
M8E 02. 11-1
Preliminary Data Sheet PN10698EJ01V0DS
11
PS9822-1,-2
Caution
GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth.

▲Up To Search▲

Price & Availability of PS9822-2-F3-N-AX

	To Download PS9822-2-F3-N-AX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .